Important information:
· No stand is included for the Premium printer. Simply place it on a high table or similar
· Only suitable for indoor use
· No direct sunlight
· The printer cannot be operated at temperatures below 10 °C and high humidity
First, please stick the return labels over the shipping labels! You also find your return labels available for download in your online customer portal!
Cable A connects the KRUU Photobooth Premium to the power outlet to supply power to the photo booth.
Cable B connects the KRUU Photobooth Premium to the Super Flash.
Cable C connects the KRUU Photobooth Premium to the Super Flash.
Connect the printer USB cable to the printer and the photo booth (USB-input). Plug the power cable of the printer into a socket.
Switch on the printer.
Pull the opening lever toward you to open the printer unit’s top door.
Align left side (1) of the ribbon shaft with the groove and then lower right side (2) of the ribbon shaft.
Close the printer unit’s top door.
Remove the printer unit’s trash box.
Remove the paper holder from the printer.
Remove the old paper roll from the paper holder, and then set the new paper roll ensuring there are no gaps. Take off the holding devices and put them on the new paper roll.
Set the paper holder into the printer.
Set the seal on the paper (-> PULL) in the same direction as shown on the left.
Remove the seal (PULL).
Remove the seal, place a hand on the paper, and rotate the paper holder in the direction of the arrow to insert the paper leading edge until the buzzer beeps.
The ERROR LED changes from flashing red and orange alternately to flashing red.
Attach the printer unit’s trash box.
Do not remove the trash box during printing. Doing so may cause trouble.
After everything is installed, the printer starts and adjusts automatically. White test prints are being made.
Head cool down
The print heads are being cooled. This error is cleared automatically.
Trash box is open / Top door is open with paper
*An error occurs if either one of them is open.
Close the trash box and/or top door.
Trash box is open/ Top door is open without paper
*An error occurs if either one of them is open.
Set the paper properly and then close the trash box and/or top door.
Paper end
Set a new roll of paper.
Ribbon end
Set a new ribbon.
Paper error
Set the paper properly.
Ribbon error
Set the ribbon properly.
Media size error
Send data with a size that matches the media size that has been set on the printer.
System error
Reset the ON/OFF switch. If the system does not recover, contact the customer service.
Pull the opening lever toward you to open the printer unit’s top door.
Rotate the paper holder by hand in the paper take-up direction to pull out the paper using the take-up force.
When pulling out the paper, pull it out slowly. If a strong force is applied, the printer may be damaged.
If the paper cannot be pulled out toward you (paper holder side), open the printer unit’s top door and then pull out the paper with the following procedure.
First remove the paper holder in the forward direction and then cut off the part of the paper that is jammed.
Remove the ribbon, insert a hand, and then grip the leading edge of the paper and pull it out toward you (direction of the arrow in the figure on the right).Wear a glove (without any fluff or powder on it) to prevent injury to your hand.
Pull the opening lever toward you to open the printer unit’s top door.
Pull out the ribbon and cut it.
Reattach the ribbon with tape or similar and Insert the ribbon back in the printer unit. Rotate the take-up roller until the part attached with tape cannot be seen anymore.
If the printer stopped with the paper partially cut, set the ON/OFF switch to OFF and then ON again. The paper jam is released and the cutter blade returns to its standby position.
Call us directly at 051 889 5703
Just send us an email to support-it@kruu.com
In case of technical questions we are available for you on Friday & Saturday until 9 pm!
For safety reasons, the following precautions must be observed!
• This photo booth is designed for 230V/50Hz AC operation in Europe.
• The device must never be connected to a power supply that deviates from the specified voltage and/or frequency values.
• For the use of the KRUU Photobooth it needs a technically faultless and with a residual current circuit breaker fused (RCD/FI), earthed Schuko socket (230V/16A). The connections used must be made by a specialist and comply with the current DIN/VDE regulations.
Protection class and usage site
The device complies with protection class 1/IP20 – permitted usage site: Indoors (no humid rooms).
Never open the casing of the photo booth, the flash, or the printer to perform any repairs or trouble-shooting of electronic parts. There are live parts in the casing of these devices, which can cause a lifethreatening electric shock if touched!
• Be sure to read these instructions in order to operate the product safely.
• Follow these instructions to prevent injury or harm to the operator of the product or others.
Warning
Denotes the risk of serious injury or death.
• Use only power sources specified in this instruction manual for use with the product.
• Do not disassemble or modify the product.
• Do not expose the product to strong shocks or vibration.
• Do not touch any exposed internal parts.
• Stop using the product in any case of unusual circumstances such as the presence of smoke or a strange smell.
• Do not use organic solvents such as alcohol, benzine or paintthinner to clean the product.
• Do not get the product wet. Do not insert foreign objects or liquids into the product.
• Do not use the product where flammable gases may be present. This may cause electric shock, explosion or fire.
• Do not touch the product connected to a power outlet during lightning storms. This may cause electric shock.
• Periodically remove any dust buildup from the power plug and power outlet using a dry cloth.
• Do not plug in or unplug the product with wet hands.
• Do not use the product if the power plug is not fully inserted into the power outlet.
• Do not expose the power plug and terminals to dirt or let them come into contact with metallic pins or other metal objects.
• Do not touch the battery charger or AC adapter connected to a power outlet during lightning storms.
• Do not place heavy objects on the power cord. Do not damage,break or modify the power cord.
• Do not wrap the product in cloth or other materials when in use or shortly after use when the product is still warm in temperature.
• Do not leave the product connected to a power source for long periods of time.
• Do not charge batteries/battery packs at temperatures outside the range of 5 – 40 °C. This may cause electric shock, explosion or fire.
• Follow any indications to turn off the product in places where its use is forbidden. Not doing so may cause other equipment to malfunction due to the effect of electromagnetic waves and even result in accidents.
Caution
Denotes the risk of injury.
• Do not touch any parts inside the product. This may cause injury.
• Avoid using, placing, or storing the product in the following places:
This may cause overheating of or damage to the printer or adapter, which may result in electric shock, burns or other injury, or fire. High temperature may deform the product or adapters.
Caution
Denotes the possibility of property damage.
• Unplug the product from the power outlet when you are not using it.
• Do not place anything, such as cloth, on top of the product while in use.
Leaving the product plugged in for a long period of time may cause it to overheat and distort, resulting in fire.
• Never reuse paper for printing, even if most of the paper is blank. Reusing paper may damage the printer if paper jams or the ink sheet adheres to the paper.
• Do not unplug the printer while it is printing. If you accidentally turn the printer off while printing, restart it and wait until the paper is ejected. If paper jams and cannot be removed, contact the KRUU Customer Support. Do not attempt to remove jammed paper by force, which may damage the printer.
• Do not use the printer near motors or other devices that generate strong magnetic fields, near TVs or radios, or in dusty environments. This may damage the printer or cause malfunction.
• Do not raise the monitor excessively. The screen can be raised to about 45°. Attempting to raise it further may damage it.
IMPORTANT: Turn off the printer, unplug it from the outlet, wait about 14 seconds, plug it back in, and turn it back on. Then, follow the steps in the video.